The LightMAX MiniPro EYECONIC™ LED system consists of the following key components:

• 2 x Silicone LED Patches
• 2 x Magnetic 2 pin, 4mm to USB A Charging Cables
• 29 x Individually Wrapped Hydrocolloid Patches including 1 Sensitisation Patch
• 1 x User Manual
• 1 x Travel Pouch

Pro-tip: The LightMAX MiniPro EYECONIC™ LED can be used in any target areas like nasolabial folds, forehead, or even on the body in areas that need localised repair.

DIRECTIONS:

For optimal results use 10 mins daily, 3-5 times per week. For all product information, visit the user manual.

1. Remove the contents of the LightMAX MiniPro EYECONIC LED box.
2. Peel the device side of the Hydrocolloid Patch.
3. Attach it to the LightMAX MiniPro EYECONIC LED device.
4. Once secured to the device, peel the face side of the Hydrocolloid Patch.
5. Press firmly onto your under-eye area until secure.
6. Hold down the power button on each device until LED lights appear.
7. After 10 minutes the LED device will automatically turn off signaling the end of your treatment.
8. Remove gently from the skin.
9. Remove the Hydrocolloid Patches from the LED and discard them.
10. Using your ring finger, apply a small amount of Soothe & Smooth to the under eyes

Pro-tip: The LightMAX MiniPro EYECONIC™ LED can be used in any target areas like nasolabial folds, forehead, or even on the body in areas that need localized repair.

Using LightMAX MiniPro EYECONIC™ LED:

Regarding electromagnetic compatibility (EMC) and electromagnetic fields (EMF), in and around the home environment the LightMAX MiniPro EYECONIC™ LED should be kept away from radio frequency (RF) equipment to avoid interference.

Treatment Recommendations:

For the treatment of facial wrinkles, the best results are seen by treating for 3-5 times a week for 6 weeks. Maintenance treatment should be carried out as required, according to lifestyle and skin condition.

Carrying out a treatment:

• DO NOT over flex the LightMAX MiniPro EYECONIC™ LED device. Although it is flexible, it is not designed to withstand excess bending or folding.
• DO NOT use the LightMAX MiniPro EYECONIC™ LED without a Hydrocolloid Patch.
• Ensure LightMAX MiniPro EYECONIC™ LED is fully charged before commencing a treatment session.
• Cleanse or exfoliate the skin to remove any traces of skincare.
• Use a new Hydrocolloid Patch every treatment session.
• See the “How to use the Hydrocolloids” section for a step-to-step guide to using the Hydrocolloids.
• Peel the device side of the backing paper off an adhesive Hydrocolloid Patch.
• Place the sticky side of the adhesive Hydrocolloid Patch onto the LED side (white) of the LightMAX MiniPro EYECONIC™ LED. Ensure the adhesive Hydrocolloid Patch aligns with the shape of the LightMAX MiniPro EYECONIC™ LED.
• Press down across the entire surface of the adhesive Hydrocolloid Patch.
• Peel the face side of the backing paper from the adhesive strip.
• Using a mirror position the LightMAX MiniPro EYECONIC™ LED over the treatment area.
• Switch ON the LightMAX MiniPro EYECONIC™ LED. The device will automatically switch OFF after 10 minutes. You may stop the treatment at any time by pressing the ON/OFF button.
• After the treatment, carefully remove the LightMAX MiniPro EYECONIC™ LED and adhesive Hydrocolloid Patch from the treatment area.
• Remove the adhesive Hydrocolloid Patch from LightMAX MiniPro EYECONIC™ LED and discard in general household waste. If you would like to keep the Hydrocolloid Patch on the treatment area after the LED treatment cycle has finished, press the Hydrocolloid Patch onto the face using the tab and carefully peel the LED device from the Hydrocolloid Patch.
• Clean LightMAX MiniPro EYECONIC™ LED by following the instructions in “Cleaning the LightMAX MiniPro EYECONIC™ LED device”. Ensure that the device is NOT being charged when cleaning.
• You may treat more than one treatment area in a treatment session.
• DO NOT repeat a treatment on the same treatment area in the same session.

Care and Maintenance:

• The lifetime of the lithium battery can be maximized by allowing it to fully charge and then fully discharge during regular use.
• Store LightMAX MiniPro EYECONIC™ LED at room temperature in dry conditions.
• Avoid storing LightMAX MiniPro EYECONIC™ LED in dusty conditions, in direct sunlight or in damp and humid conditions.
• LightMAX MiniPro EYECONIC™ LED contains no serviceable parts.
• Before each use, with the device switched off, clean the LightMAX MiniPro EYECONIC™ LED following the cleaning instructions below. DO NOT use the LightMAX MiniPro EYECONIC™ LED device any longer if it shows any signs of damage to the material through wear and tear.
• DO NOT use the Hydrocolloid after its expiry date.
• DO NOT use the LightMAX MiniPro EYECONIC™ LED if it has been exposed to environmental conditions outside of those specified in the Technical Specification.

Cleaning the LightMAX MiniPro EYECONIC™ LED Device:

• Before cleaning, ensure that the charging cable is disconnected from the LightMAX MiniPro EYECONIC™ LED and that the device is not charging.
• Clean the LightMAX MiniPro EYECONIC™ LED with a water-based wipe. Stubborn stains or adhesive residue can be removed by wiping gently with 70% alcohol.
• DO NOT use water to clean LightMAX MiniPro EYECONIC™ LED.
• DO NOT use the device if you think it has come into contact with water.

RITUALS:

Use the LIGHTMAX MINIPRO EYECONIC™ LED for 10 mins daily, 3-5 times per week. Finish by applying a small amount of Soothe & Smooth to the under-eye area.